Adding internal Bluetooth

I took power for the new USB port from the existing port since the chipset has a specific power plane that is used for the USB system. The data pins I got from tapping the docking station connector. The wire I used was from an old PS2 mouse; the mouse cable has four different coloured wires the perfect size for what I needed. I ran the wires up over the top of the board but that was probably a bad idea, next time I would run them underneath to keep them out of the way.

With everything connected it was time to test it out. Success!! I had a few issues at first because I didn’t have good connections but once I fixed them it worked fine. Here it is all wired up and nestled in its new home. I ended up running some extra wire to the connector then folding it over to get it to sit nicely in the opening. I thought I might have to pad it a bit to stop it from rattling but the extra wire took care of that for me.

I plugged in a USB thumb drive in the back and it still worked fine. Here’s the details for the USB hub now showing two devices connected. The only downside to this hack is that because of the way the docking station works you will only be able to use one of the USB ports on it since one will always be used for the Bluetooth. I don’t have a docking station so that doesn’t really matter to me. It’s much more useful have the second port all the time instead of just with the docking station. Because I used a standard USB connector I could switch out the Bluetooth with a Wi-Fi adapter if I found that to be more useful (assuming I could cram it inside somewhere).

Return to the projects index page

16 Responses to “Adding internal Bluetooth”

1. lalaland Says:
   December 30th, 2005 at 16:15

   First Post!

   Hmmm isn’t this just a rip off of other projects about embedding wlan in a laptop?

2. Chris J. Says:
   December 31st, 2005 at 12:04

   lalaland: I wouldn’t say so as Tom is doing it in a different way by connecting the Bluetooth dongle direct to the existing usb controller and thus is using unallocated resources. Many other projects include installing an completely new usb hub.

3. Pointman Says:
   January 10th, 2006 at 21:38

   Heads-up for anyone who may have written this option off because they don’t see additional USB ports in their hardware profile…

   I sympathize with the need for this project as I also only have one USB port on my Dell Inspiron 4150 laptop. However, I was faced
   With an additional challenge since no unallocated USB ports show up in my hardware device manager. After some research I learned
   that the bridge chip does, in fact, offer up to 3 USB ports but two are disabled by low-level software (preventing them from even
   showing up in the hardware profile) unless the laptop is docked. After ohming out a few of the docking port pins I was able to
   trick the laptop into thinking it was docked by tying pin 54 (labeled “Docked” in a service manual that cost me $5 on the web) high
   with a 2k resistor to pin 98 (labeled “+5Vsus” in the same manual). Bingo! Now I had access to TWO additional USB ports. I
   installed a BlueTooth dongle and then brought the other USB signals to a 4-pin header that I can choose to use at a later time.

   The only risk is that telling the laptop that it is docked may, in fact, be enabling lots of other unnecessary functionality which may
   in turn affect my battery life.(Assuming that the laptop counts on full A/C power when docked and doesn’t much care about conserving
   battery life at that point?) We’ll have to see how it performs over time…

   Also, a heads-up for anyone who happens to use the same Dell service manual I found: The pin numbering listed for the docking port
   is reversed! Hard to explain without the diagram in front of you, but I would strongly recommend ohming out a few of the known
   pins(ground, parallel port pins, etc.) to confirm whether or not the figure is true or reversed.

4. aZzA Says:
   February 2nd, 2006 at 9:46

   Oh… Nice Job!!!

5. Xavier Says:
   February 8th, 2006 at 9:34

   well I was wondering how can I add internal bluetooth to my sony VGN FJ170B

6. d1 Says:
   March 30th, 2006 at 11:22

   Wouldnt it work for those “flash drives” for my FOSA NB-34B? I sort of needed more hard disk storage since i got lots of things and junk crammed in its small 20Gb hard disk.

7. Shpimuletz Says:
   June 14th, 2006 at 10:23

   I’m just finised job an i’m not satisfied coz not work with out dock station.
   Pointman,would you like to tell as if will proced your solution with that 2k resistor,will be the problem when should conect my netbook to the dock station?

8. Shoimuletz Says:
   June 16th, 2006 at 7:57

   Done Work fine… between 54 - 98. total satisfied.Thasnk’s all.

9. alg Says:
   September 11th, 2006 at 4:44

   does anyone know what happens to this hack when you plug the laptop into a docking station (and then try to use the usb ports). Surely this will cause problems as you are trying to plug to devices in the same port without a hub, which sounds pretty dodgey to me !, and may actually damage something.

   other than that sounds intresting

10. Alexander Says:
    November 30th, 2006 at 13:17

    If you have two USB devices on the same cable–as you will here–then you most likely will not fry anything, as the usb standard is setup to detect and prevent such things from happening.

    Worst case is that none of your USB devices will work until you remove both units from the line, at which point they will be restored.

    Best case is that one of them works–the one that was connected first–and the other will cause no harm to the system.

    I would sugguest that if you have a docking station and you need more than the usb ports that it provides you purchase a hub and put it in the port that is free and epoxy over the port that is ‘in use’.

11. sjon Says:
    December 1st, 2006 at 20:14

    hello

    is it possible to connect a usb 2.0 device to the docking connector with a cable or somthing else
    please if you have a solution to help me i can use some of mine usb 2.0 devices on my laptop

    greatings,
    Sjon Kortekaas

12. adam Says:
    February 8th, 2007 at 13:35

    i brought a bluetooth wireless adapter(range:300ft)for my computer(not laptop)hoping that i could browse on the internet via another wireless in range, but unfortunately i CANT! can ANYONE PLZ PLZ give me a step by step guide on how to do this plz> thanks

13. kumar Says:
    August 5th, 2007 at 7:54

    hi i am looking for internal blutooth i have space in my laptop for blutooth my laptop acer aspire5630 if anyone know where can i buy this thank

14. dialup_2001 Says:
    October 14th, 2007 at 14:35

    Kumar, there are people on ebay who sell 8,6 or 4 pin bluetooth internal modules for the acer aspire 5630/5633 range of laptops. Because acer use the same plastics for many of there range you should already have the blueooth switch on the front. Thanks.

15. PoOh Says:
    December 28th, 2007 at 1:22

    Just done it on a Dell Latitude C400 lightweight laptop. Not that much space available to put the hacked Bluetooth adapter but it worked well . I had to do the false docking trick with pin 54 + 98. Bump for a good trick!

16. oblus Says:
    January 8th, 2008 at 6:05

    hey, from where you have this docking station connector specification, is this spec available in web?

Leave a Reply